If you haven't cleaned your eavestroughs yet, fall is the time to do it.
Eavestrough cleaning is about more than getting the leaves out before winter. A blocked trough can't drain properly, and when that water freezes, the problem can follow you through the winter.
That can mean ice buildup at the roof edge, water backing up under the shingles, or water pooling against your foundation.
So how often should you clean your gutters?
We recommend checking eavestroughs and downspouts at least twice a year, in fall and spring. But fall matters most, because you’re getting the whole drainage system ready for months of freezing temperatures, snow and ice.
A proper fall gutter cleaning doesn't take much. And while you're up there, you can catch small problems, before they turn into expensive winter repairs.
What a Clogged Eavestrough Actually Does
That ceiling stain you spot in February can trace back to clogged gutters in the fall.
When debris blocks the trough, water backs up at the eave edge instead of draining. As overnight temperatures drop, that standing water freezes into a ridge. Snow melting on the warmer upper roof runs toward that ridge and has nowhere to go except back under the shingles. In Calgary, Chinook thaws make this worse by dumping meltwater onto frozen eaves.
That’s the start of an ice dam, which can cause winter leaks even when the shingles are in good shape. Ice dams begin when a warm attic melts roof snow that then refreezes at the cold eave. A clogged eavestrough doesn’t start that process, but it gives the ice a place to build.
The second damage path runs downward. A blocked downspout dumps water against the foundation, where it pools, freezes and expands. Over repeated freeze-thaw cycles, that can damage the foundation wall.
How to Clean Your Eavestroughs Safely

Wait until leaves have finished falling before climbing up. Cleaning too early means doing it twice, but on the Prairies, freeze-up can follow within weeks.
What you need: Work gloves, a bucket or yard waste bags, a garden hose with a pressure nozzle, and a stable ladder.
The process:
- Position your ladder on firm, level ground. If you can, have a partner steady the base, especially if the ground is soft or uneven.
- Scoop out debris by hand, starting near the downspout outlet and working away from it. That way, you won’t push leaves into the outlet and clog it.
- Flush from the far end toward the downspout with a garden hose.
- Check downspout flow at the ground. Water should come out freely and, if possible, land at least 2 metres from the foundation wall.
Ladder safety note: Ladder falls are a consistent contributor to injury-related emergency room visits in Canada, says the Canada Safety Council. Always move the ladder rather than reaching sideways, keep three points of contact, and never overreach.
The Case for Leaf Guards
If the ladder work puts you off, leaf guards are a more permanent solution.
Quality mesh guards sit flush on the eavestrough and allow water through while blocking the leaves, pine needles, and seed pods that cause the bulk of autumn blockage.
They reduce eavestrough cleaning from a time-sensitive twice-a-year task to an annual check, so you’re no longer racing the first freeze. At Advanced Level Roofing, we match the guard to your trees and roof, because no single product suits every home.
What to Check While You're Up There

Being up at eavestrough level is the best chance you’ll get to see the system’s real condition. Here are four checks worth doing while you're cleaning:
- Pitch. Water should flow steadily toward the downspout with no pooling mid-run. Standing water after flushing means the slope has settled and the hangers need adjusting.
- Separation from the fascia. Run a hand along the back edge of the eavestrough. Any gap between the trough and the fascia board means the hangers have pulled out. When that happens, water runs behind the trough instead of through it, and the fascia soaks it up.
- Corner and joint seams. Flush water toward the corners and watch for seepage. A seeping joint needs resealing now and a tube of eavestrough sealant is a small cost at cleaning time. Left through a Canadian winter, freeze-thaw cycles can turn a weeping seam into a split one.
- Fascia board condition. Check the fascia face below the eavestrough for staining, softness, or discolouration, which point to water running behind the trough.
Our lead technician adds, “When we're at eavestrough level on a fall job, we almost always find at least one joint that's starting to let go. The homeowner has been walking past it for two years at ground level and hasn't noticed. Caught at cleaning time, it's a quicker fix. Caught a few months later after a winter of freeze-thaw cycling, it's a section replacement.”
When Cleaning Reveals a Replacement Need
Sometimes cleaning shows that the eavestrough itself is the problem. These signs point toward replacement rather than repair:
- Visible rust, cracking, or holes in the trough face. Minor surface corrosion may be manageable, but widespread rust, cracks, or holes mean the trough can no longer contain and direct water reliably.
- Persistent seam failures despite repeated resealing. If the same joints keep leaking after repairs, the problem is more likely the age and condition of the eavestrough than the sealant.
- Multiple sections pulling away from the fascia. When several sections are sagging or pulling away, it can point to failing hangers, weakened fascia, or a system that costs more to keep repairing than to replace.
- A system that’s 20–25 years old or more. Age alone doesn’t call for replacement, but older systems tend to accumulate problems that are worth assessing.
Seamless aluminum eavestrough, formed on-site to the exact length of each run, has fewer joints to fail than a sectional system—worth asking about if you’re replacing.
Make Sure Your Eavestroughs Are Ready for Winter
A fall eavestrough cleaning isn't really about clearing the leaves. It's about making sure water has somewhere to go when temperatures drop.
If the troughs are clear, the downspouts are flowing, the pitch is right, and the system is still securely attached to the fascia, you've taken care of one of the most preventable causes of winter drainage problems.
And if you still get heavy ice buildup every winter despite clean, properly functioning eavestroughs, the cause is more likely heat escaping into your attic. The permanent fix is air sealing, insulation and ventilation. Where complex roof geometry makes perfect ventilation hard to achieve, SmartMelt™ de-icing can supplement that work by managing the ice at the eave.
Not sure what you're looking at?
We can help you tell whether it's a simple maintenance issue or something that needs repair or replacement. We offer a free estimate using satellite imagery for a general assessment. For a closer look, our on-site home assessment is a paid visit that covers the roof and drainage system and comes with a written report and photos.
Call Advanced Level Roofing at 1 (866) 334-3705, or fill out our estimate form.
Serving Calgary, Edmonton, Winnipeg and surrounding communities.